Sparkfun Esp32 Thing Kiwi Electronics I connected one differential i2c module on each end of a cat 5e cable, on one side is an i2cdriver connected via qwiic, on the other is a sparkfun ublox gps module and one other sparkfun sensor board. the pull ups are enabled everywhere, and an i2c scan yields nothing. i suspect i need to remove at least some pull ups, but i'm not clear on where they should be enabled in a point to point. Jetpack questions & or issues related to products in the robotics category should be posted in this forum. includes direct current (dc) motors & drivers, general hardware & chassis, servomechanisms (servos) & drivers, stepper motors & drivers, etc. search 7 posts reply.

Sparkfun Thing Plus Esp32 S3 Opencircuit Re: sparkfun nano power timer tpl5110 #205844 by el duderino fri jul 12, 2019 10:54 am hi again gkm,. If i understood correctly the artemis global tracker is configured to work with the rockblock provider and it’s message based. i need to send a block of data that can be 8kbytes.do you know if it can be used with other provider that support connected mode? with connected mode i mean that the modem make a call to another modem to establish a tcp connection. Hi, i setup the antenna and have started logging. i note something very strange: with just the faucet i get the location almost spot on (100mm) and on google maps it shows the correct location. the reference station is reporting it's location almost exactly 3m north of it's true location ( the error), east west is correct. when i use the faucet with the correction data from the reference. Sparkfun don't actually make the vl53l1x chips, we just solder them to our own board so our knowledge on the inner workings isn't as great as the manufacturers would be.

Sparkfun Esp32 Thing Hi, i setup the antenna and have started logging. i note something very strange: with just the faucet i get the location almost spot on (100mm) and on google maps it shows the correct location. the reference station is reporting it's location almost exactly 3m north of it's true location ( the error), east west is correct. when i use the faucet with the correction data from the reference. Sparkfun don't actually make the vl53l1x chips, we just solder them to our own board so our knowledge on the inner workings isn't as great as the manufacturers would be. Re: lsm6dso spi connection #235148 by kro10000 tue aug 09, 2022 5:49 am some photos, i followed the same pinout from the sparkfun diagram. Single servo control #249704 by timehunter mon jun 03, 2024 7:32 am no idea which forum to post this on. tried it on the "kits" forum with no results. would be great if sparkfun had a kit to control a single servo. something simple. i am an old fart and do not need to learn arduino or any of that other stuff. i just want to control the position and speed of a single servo. i need something. I have two micro oled qwiic boards (product lcd 14532 .) one has been working without fail for several weeks. the other one, i hooked up to an artemis redboard (via 50mm qwiic cable) last night for the first time, and ran a test program that cycles through 64 64x48 bitmaps, at one per second, then starts over. i left the program running overnight when i checked it after about 6 hours, the. Have questions about a sparkfun product or board? this is the place to be. 8 posts 8 posts.

Sparkfun Thing Plus Esp32 C6 Opencircuit Re: lsm6dso spi connection #235148 by kro10000 tue aug 09, 2022 5:49 am some photos, i followed the same pinout from the sparkfun diagram. Single servo control #249704 by timehunter mon jun 03, 2024 7:32 am no idea which forum to post this on. tried it on the "kits" forum with no results. would be great if sparkfun had a kit to control a single servo. something simple. i am an old fart and do not need to learn arduino or any of that other stuff. i just want to control the position and speed of a single servo. i need something. I have two micro oled qwiic boards (product lcd 14532 .) one has been working without fail for several weeks. the other one, i hooked up to an artemis redboard (via 50mm qwiic cable) last night for the first time, and ran a test program that cycles through 64 64x48 bitmaps, at one per second, then starts over. i left the program running overnight when i checked it after about 6 hours, the. Have questions about a sparkfun product or board? this is the place to be. 8 posts 8 posts.

Github Sparkfun Sparkfun Thing Plus Esp32 S3 A Sparkfun Thing Plus I have two micro oled qwiic boards (product lcd 14532 .) one has been working without fail for several weeks. the other one, i hooked up to an artemis redboard (via 50mm qwiic cable) last night for the first time, and ran a test program that cycles through 64 64x48 bitmaps, at one per second, then starts over. i left the program running overnight when i checked it after about 6 hours, the. Have questions about a sparkfun product or board? this is the place to be. 8 posts 8 posts.

Sparkfun Thing Plus Esp32 Wroom Usb C Opencircuit